High Tech Industrial Representation, Inc.
  • Home
  • Products
    • AB Tools
    • AKS Teknik
    • Champion Tool Storage
    • Eppinger
    • Jergens
    • Kyocera Precision
    • SGS Precision Tools
    • K-Tool
    • Masa Tool
    • Oemeta Coolant
    • Preferred Abrasives
    • Techniks Tool Group
  • About
  • Journal
  • Services
  • Promotions
  • Contact
  • Home
  • Products
    • AB Tools
    • AKS Teknik
    • Champion Tool Storage
    • Eppinger
    • Jergens
    • Kyocera Precision
    • SGS Precision Tools
    • K-Tool
    • Masa Tool
    • Oemeta Coolant
    • Preferred Abrasives
    • Techniks Tool Group
  • About
  • Journal
  • Services
  • Promotions
  • Contact
Search

Don't Take Your Retention Knobs for Granted

2/24/2021

0 Comments

 
by Bernard Martin
Retention Knobs are the critical connection between your machine tool and the tool holder and they are the only thing holding a steep taper tool holder in the machine’s spindle.
Retention knob pull stud casues of failure
​Techniks has recently introduced their MegaFORCE retention knobs that have some rather unique features when compared to standard pull studs.  

​Before delving into the features of the MegaFORCE pull studs, let's review some things that you may not know, or think about, on a daily basis. 


Retention knobs go through thousands of tool changes which means that they are subjected to the very high pulling forces from the spindle’s drawbar.

This force can be up to 2300 ft. lbs. for 40 taper toolholders and up to 5000 ft. lbs. for 50 taper toolholders. According to Haas, you should expect a service life of about 6000-8000 hours for a retention knob.  

​Most all rotary toolholder manufacturers state that you should be replacing your pull studs at least every three years.
However, if you're running multiple shifts, 24-7, making lots of tool changes, making very heavy cuts with long reach or heavy cutting tools, and/or have ball lock style grippers instead of collet type grippers used on the retention knob, you will probably need to replace your studs at least every six months.

Given the spindle speeds that we are running at to remain competitive, retention knobs are not an item that you want to take a chance on breaking.  I can tell you firsthand that 5 pound toolholder with a drill in it flying out of the spindle at 23,000 RPM is not something you want to experience. ​

Metal Fatigue: Why Pull Studs Fail

Pull studs encounter catastrophic failure as a result of metal fatigue. The metal fatigue can be caused by a number of reasons including poor choice of base material, engineering design, machining process, poor heat treatment, and, sometimes, they have just met or exceeded their service life. We're going to dig into each of these reasons below but first let's look at some threading fundamentals.
The threads on your retention knob will stretch slightly when load is applied and the loading borne on each thread is different. When you apply a tensile load on a threaded pull stud, the first thread at the point of connection sees the highest percentage of the load.

The load on each subsequent thread decreases from there, as show in the table. Any threads beyond the first six are purely cosmetic and provide no mechanical advantage. 
Percentage of Load on a Retention Knob Thread
Percentage of Load on each thread of a Retention Knob.
Additional threads beyond the sixth thread will not further distribute the load and will not make the connection any stronger. 

That is why the length of engagement of the thread on a pull stud is generally limited to approximately one to one & a half nominal diameter. After that, there is no appreciable increase in strength. Once the applied load has exceeded the first thread's capacity, it will fail and subsequently cause the remaining threads to fail in succession.

Retention Knob Design

Repetitive cycles of loading and unloading subject the retention knob to stress that can cause fatigue and cracking at weak areas of the pull stud.
What are the weak areas of a standard retention knob?  

​For the same reason we put corner radiuses on end mills, sharp corners are a common area of failure for any mechanical device.

​The same holds true with your pull studs:  The sharp angles on the head of the retention knob and at the minor diameter of the threads are common locations of catastrophic material failure.
The most common failure point for a retention knob is at the top of the first thread and the underside of the pull stud where the grippers or ball bearings of the drawbar engage and draw the toolholder into the spindle.

Remember, bigger Radii are stronger than sharp corners. ​More on that soon.
Retention Knob Metal Fatigue
These are the two weakest points of any retention knob.
Styles of Retention Knob for Rotary Toolholder
Styles of MegaForce Retention Knobs

Material

Not all retention knobs are made from the same material, however, material alone does not make for a superior retention knob. Careful attention to design and manufacturing methods must be followed to avoid introducing potential areas of failure.

​Techniks MegaFORCE retention knobs are made from 8620H. AISI 8620 is a hardenable chromium, molybdenum, nickel low alloy steel often used for carburizing to develop a case-hardened part. This case-hardening will result in good wear characteristics.  8620 has high hardenability, no tempering brittleness, good weldability, little tendency to form a cold crack, good maintainability, and cold strain plasticity.

There are some companies making retention knobs from 9310. The main difference is the lower carbon content in the 9310. 9310 has a tad more Chromium, while 8620 has a tad more nickel.  Ultimate Tensile Strength (UTS) is the force at which a material will break. The UTS of 8620H is 650 Mpa (megapascals: a measure of force). The UTS of 9310H is 820 Mpa. So, 9310H does have a UTS that is 26% greater than 8620H.

​That said, ​Techniks chose 8620 as their material of choice because of the higher nickel content.  Nickel tends to work harden more readily and age harden over time which brings the core hardness higher as the pull stud gets older. The work hardening property of 8620 makes it ideally suited for cold forming of threads on the MegaFORCE retention knobs.

​It should be noted that some companies are using H13. H13 shares 93% of their average alloy composition in common with 9310. 
5. Cut thread vs rolled thread retention knob
A cut thread, image 1, has a higher coefficient of friction due the the cutting process, while a roll formed thread, image 2, has a lower coefficient of friction which means that it engages deeper into the toolholder bore when subjected to the same torque. You will notice that Cutting threads tears at the material and creates small fractures that become points of weakness that can lead to failure. Rolled threads have burnished roots and crests that are smooth and absent of the fractures common in cut threads.

​Rolled Threads vs. Cut Threads

Rolled threads produce a radiused root and crest of the thread and exhibit between a​ 40% and 300% increase in tensile strength over a cut thread. The Techniks MegaFORCE retention knobs feature rolled threads that improve the strength of the knob by 40%.  
LMT Fette - Thread rolling with F2 Rolling head on CNC lathe
Fette F2 Thread Rolling Head
In cold forming, the thread rolls are pressed into the component, stressing the material beyond its yield point. This causes the component material to be deformed plastically, and thus, permanently.

There are three rollers in the typical thread rolling head that maintain better concentricity by default than single point cutting of the threads.

​Also, unlike thread cutting, the grain structure of the material is displaced not removed.

Shown here is a Fette F2 head cold forming a thread. Note how the three roller forms center and maintain near perfect concentricity of the pull stud shaft.


​Rolled threads produce grain flows that follow the contour of the threads making for a stronger thread at the pitch diameter which is the highest point of wear. 

The cold forming process also cold works the material which takes advantage of the nickel work hardening properties of 8620.
By comparison, cut threads interrupt the grain flow creating weak points.
MegaForce Retention Knob features
Photo courtesy Mike Roden at Fette Tool. www.turningconcepts.com

MegaFORCE Geometric Design Features

Picture
Features of Techniks MegaFORCE Retention Knobs
Overall Length
There are some claims that a longer projection engages threads deeper in the tool holder preventing taper swelling. While a deeper thread engagement can help prevent taper swelling, applying proper torque to the retention knob is an effective way to reduce taper swelling.

An over-tightened retention knob may still cause taper swelling regardless of how deep it engages the threads of the tool holder. Additionally, the longer undercut section above the threads presents a weak point in the retention knob.
Blended Radii
With the new MegaFORCE pull studs, stress risers of sharp angles have been eliminated through the blended radii on the neck where the gripper engages under the head of the pull stud.  

Ground Pilot
There is a ground pilot, underneath the flange, which provides greater stability. The pilot means the center line of the tool holder and pull stud are perfectly aligned.
Magnetic Particle Tested
Each MegaFORCE retention knob is magnetic particle tested to ensure material integrity and physical soundness. MegaFORCE retention knobs are tested at 2.5X the pulling forces of the drawbar.
​
Picture
MegaFORCE Technical Specifications
  • Material: SAE8620
  • All knobs are case carbrized, hardened, and tempered to:
    • Case depth: 0.025” – 0.030”
    • Surface hardness: HRc 56-60
    • Core hardness: HRc 44 minimum
Torque Specs
The following are the guidelines for torquing your pull studs according to Techniks.
  • BT 30 36 ft. lbs.
  • ISO 30 - 36 ft. lbs.
  • 40 taper - 76 ft. lbs.
  • 50 Taper - 100 ft. lbs.

​Retention Knob Best Practices

In order to maximize the life of your retention knob and prevent catastrophic failure here are some technical tips to keep your shop productive and safe.
  • Regularly inspect retention knobs for signs of wear. Wear may appear as dimples or grooves under the head or visible corrosion anywhere on the retention knob. 

  • If the retention knob demonstrates any signs of wear replace it immediately. ​
​
  • Make sure to properly torque the retention knob to the manufacturer’s specifications. Use a torque wrench and retention knob adapter to ensure proper torque. 
Broken Pull Stud
  •  Overtightening can overly stress the retention knob leading to premature failure and can cause the tool holder taper to swell leading to a poor fit between the machine spindle and the tool holder.
​
  • Apply a light coat of grease to the retention knob MONTHLY to lubricate the drawbar. If you use through-spindle coolant (TSC), apply grease to the retention knobs WEEKLY.

Indication Marks on Pull Studs ​is NOT Normal

Damaged Retention Knob
Damaged Retention Knob. photo courtesy Haas Automation. Click photo for original content.
There have been some who claim that drawbar gripper fingers and/or ball marks that appear on retention knob head after several tool changes is normal.

It is NOT.  THAT IS FALSE. 

According to Haas CNC, ball or gripper marks on the edge of the pull stud indicate that the drawbar does not open completely.

​If you see these indication marks you should check your drawbar and replace these pull studs immediately.

Special thanks for Greg Webb at Techniks and Mike Roden from Fette Tools/ Turning Concepts, for providing technical insights. ​
0 Comments

The Advantages of Balax Thread Gages

4/18/2018

0 Comments

 
Precision Ground Taperlock Thread Gages made by Balax have some very unique design, enginering, and production properties that distinguish them from most other thread gage manufacturers.  Even with all of these advantages they remain competitively priced!
Picture
Superior Metallurgy
  • Made from High Speed Tool Steel., the same material as used in tap manufacturing.
  • Heat treated to 63-65 Rockwell C , the same hardness as used in tap manufacturing.

Superior
Accuracy
  • Threads are  ground on proprietary Balax Thread grinders. This unique grinding process provides accurate thread profiles with less lead error than other gage grinding methods used today.
Balax “BALanced AXially
Similar to Balax Thredfloer Taps, Gages are ground on proprietary equipment to prevent lead error.
Balax Extra Long Go Gage
Extra Length Feature
Balax "go" gages in sizes 4-40 (M3 x .5) and larger are made with a relieved or undercut thread section.

This
longer-than-standard length feature allows gaging to thread depths achieved with standard tap thread lengths.

Reversible gages are no longer
required to check deep tapped holes
Miniature Gages
Available in sizes ranging from 000-120 to 00-90 or .90 UNM to 1.40 UNM.
The high quality materials and special grinding process
used to manufacture Balax Miniature gages provide a consistency and accuracy never before available with miniature gages. They are held in special collect type holders.
Certificate of Inspection
All Balax Thread gages are furnished with actual fifth place (.00000) measurements of pitch diameter and major diameter to guarantee the accuracy of your gage to Class-X ̋tolerance levels.
Balax Certificage of Inspection Thread Gage
Titanium Nitrided
Titanium Nitrided thread gages are available for all stock sizes.


Special Gages
Balax can custom manufacture gages to your specifications.
0 Comments

    News & Applications

    Learn about the latest breaking news and applications that we're working on right here!

    Archives

    June 2022
    February 2021
    February 2020
    September 2019
    April 2019
    March 2019
    February 2019
    November 2018
    September 2018
    July 2018
    June 2018
    May 2018
    April 2018
    February 2018
    September 2016
    February 2014
    July 2012

    Categories

    All
    3D Printing
    Back Counterbore
    Balax
    Ball Lock
    Case Study
    Collet
    High Tech
    IMTS
    Inspection Certificate
    Jergens
    K-Tool
    Kyocera SGS
    Maintenance
    Mark Hurst
    Martin Trunnion
    Masa Tool
    Miniature Gages
    Prototyping
    Pull Studs
    Retention Knobs
    Rotary Toolholders
    Runout
    Steel 4140
    Taper
    Techniks
    Threadfloer
    Thread Forming
    Thread Gages
    Todd Pakiz
    Trunnion Table
    Video
    Visualization
    Workholding
    Z- Carb
    Zero Point System

    RSS Feed

ABOUT
JOURNAL
CONTACT

High Tech Industrial Representation, Inc.

16610 Legacy Lane
​New Prague, MN 56071
612-712-4847
​[email protected]
© 2024  High Tech Industrial Representation, Inc.  All Rights Reserved
web design by Rapid Production Marketing
  • Home
  • Products
    • AB Tools
    • AKS Teknik
    • Champion Tool Storage
    • Eppinger
    • Jergens
    • Kyocera Precision
    • SGS Precision Tools
    • K-Tool
    • Masa Tool
    • Oemeta Coolant
    • Preferred Abrasives
    • Techniks Tool Group
  • About
  • Journal
  • Services
  • Promotions
  • Contact